Overview
LiftOff spelen met de Turnigy TGY-i6 of FlySky i6 met de audio kabel, zonder USB simulator.Playing LiftOff with the Turnigy TGY-i6 or FlySky i6 using a audio cable, without USB simulator.Jouer à LiftOff avec le Turnigy TGY-i6 ou le FlySky i6 en utilisant un cable audio, sans l’USB.
Schoon Vlaams
Installeer SmartPropoPlus[www.smartpropoplus.com].
Wis het bestand SppProcess.dll en vervang het door de kopie op het forum[www.smartpropoplus.com].
Normaalgezien moet vJoy met SmartPropoPlus mee geinstalleerd worden, maar anders vind je het hier[vjoystick.sourceforge.net]
Fatshark FPV PS2/3.5mm JR HT Connection Cable
Zender
Je moet geen bijkomende instellingen doen in de zender, maar om zeker te zijn:
- AFHDS 2A is ON
- PPM output is OFF
- Trainer mode is OFF
- Student mode is OFF
Prop de kabel in de zender, en het andere einde in de microfooningang van de PC.
Start SmartPropoPlus.
SPP werkt met geluid. Als hij niets hoort, controleer of hij op de juiste input zit. Dit kan je doen door rechts te klikken op de luidspreker, en “opnameapparaten” te selecteren. De microfoon zou moeten spelen. Als hij op het verkeerde apparaat zit, SPP afsluiten, het juiste apparaat als standaard instellen en SPP opnieuw starten.
Het geluidsniveau van mijn microfoon was te laag, en hij verbrak telkens de connectie. Een update van de drivers heeft dit probleem verholpen.
Signal decoder is PPM Walkera. De balkjes moeten mee bewegen met uw sticks.
Hier was een probleem met offset, en door het bestand SppProcess.dll te vervangen werd dit opgelost.
Nihil
Hier is het de bedoeling dat je de kanalen van de zender mapt op de kanalen van de virtuele joystick vjoy. Start “Configure Vjoy” en maak een joystick met vier assen.
X=1
Y=2
Z=3
Rz =4
Knoppen kunnen hier ook ingesteld worden in functie van wat ge zelf leuk vindt.
Nihil.
Start Liftoff en calibreer de besturing.
English
Install SmartPropoPlus[www.smartpropoplus.com].
Delete the file SppProcess.dll and replace it by the copy on the forum[www.smartpropoplus.com].
vJoy should be installed along with SmartPropoPlus, buuutt:here[vjoystick.sourceforge.net]
Fatshark FPV PS2/3.5mm JR HT Connection Cable
Transmitter
You do not need to adapt anything in the transmitter, but to be sure:
- AFHDS 2A is ON
- PPM output is OFF
- Trainer mode is OFF
- Student mode is OFF
Put the cable in the transmitter, and the other end in the microphone in of your PC.
Start SmartPropoPlus.
SPP works with sound. In case it does not hear anything, check if you are using the right device. This can be done by right clicking on the speaker icon and selecting recording. The microphone should play when the transmitter is on. If the microphone plays on the wrong device, select this device as default, and reboot SPP.
The sound level of my mic was too low, and a driver update fixed this.
Signal decoder is PPM Walkera.The bars should move along with the sticks.
There was a problem with the offset and noise, but replacing the file in Program Files fixed this.
Nihil
You should map the channels of your TX to the virtual joystick vJoy.. Start “Configure Vjoy” en make a joystick with four axis.
X=1
Y=2
Z=3
Rz =4
Buttons can also be implemented here according to your liking.
Nihil.
Start Liftoff calibrate the controls.