Overview
Standard of Interchangeability Between Tractors and TrailersThis standard is designed to ensure the interchangeability of truck tractors and semi-trailers of different authors among themselves.We will be happy if you develop your tractors and trailers in accordance with this standard.
Main dimensions
To ensure the interchangeability of tractors and trailers, their dimensions in the area of the coupling must satisfy the following requirements:
- Only electric saddle connector with key or toggle button switch for disconnecting
- 11 blocks – truck and trailer width
- 8 blocks – min distance from the saddle pin to the rear wall of the tractor cab
- 8 blocks – max distance from saddle pin to rear of truck frame
- 9 blocks – min distance from the saddle pin to the low part of the trailer (for example, to the paws of the trailer, or platform of lowboy trailer)
- 6 blocks – max distance from pin to trailer front wall.
- Electric cable anchors for connecting the power supply of trailers (Yellow) and transmitting the composite signal (Violet)
Recomended basic dimension is a 5 blocks for flatbed and box trailers. You can use the 6th block for installation of refrigeration equipment, for curved wall of the trailer or other special cases.
===rus===
Для обеспечения взаимозаменяемости тягачей и прицепов их размеры в зоне сцепки должны удовлетворять следующим требованиям:
- Только электрический коннектор седла с ключом или кнопкой для отсоединения
- 11 блоков – ширина грузовика и трейлера
- 8 блоков – макс расстояние от пина седла до задней части рамы грузовика
- 8 блоков – мин расстояние от пина седла до задней стенки кабины тягача
- 9 блоков – мин расстояние от пина седла до низкой части трейлера (например до опускающихся лап трейлера)
- 6 блоков – макс расстояние от пина до передней стенки трейлера
- Электрические кабельные якоря для подключения электропитания прицепов (Желтый) и передачи композитного сигнала (Фиолетовый)
Рекомендуется длина в 5 блоков для обычных прицепов-платформ и шторных прицепов. Вы можете использовать 6-й блок для установки холодильного оборудования, для устройства выгнутой стенки прицепа или других особых случаев.
Microcontrollers (optional)
Two microcontrollers are included that you can install to transfer data between the tractor and trailer. A tractor-mounted microcontroller is not necessary if you provide data transmission via a composite signal through the fifth wheel coupling connector.
These two universal controllers support the transmission of data both through the signals “on / off” and “number”, and through a composite signal. In the properties of the microcontroller, you can select the operating mode. In any case, the transfer of data from the tractor to the controller in the trailer is via a composite signal.
In order not to install the controller in the tractor, you can apply a composite signal to the saddle with the following codes:
- 1 – left turn signal
- 2 – right turn signal
- 3 – brake lights
- 4 – reverse
- 5 – marker lights
- 6 – parking brake
Numerical Signals: - 1 – Brake
- 2 – Turning the wheels of the trailer
===rus===
Прилагаются два микроконтроллера которые вы можете установить для передачи данных между тягачом и прицепом. Микроконтроллер на тягаче не обязателен, если вы обеспечите передачу данных по композитному сигналу через коннектор седельно-сцепного устройства.
Эти два универсальных контроллера поддерживают передачу данных как через сигналы “on/off” и “number”, так и через композитный сигнал. В любом случае передача данных от тягача к контроллеру в прицепе осуществляется через композитный сигнал.
Для того чтобы не устанавливать контроллер в тягаче, вы можете подать композитный сигнал на седло со следующими кодами:
- 1 – левый сигнал поворота
- 2 – правый сигнал поворота
- 3 – стоп-сигнал
- 4 – задний ход
- 5 – габариты
- 6 – парковочный тормоз
Численные сигналы: - 1 – Тормоз
- 2 – Поворот колёс прицепа