Overview
If you’re like me (a bit of an idiot) you might find a slightly more step-by-step list of the car parts useful.So here’s what’s basically the guide on the wiki, re-written in the order done in the tutorial videos by DeivisBicepsGood luck!
FULL GUIDE
NIP TO THE SHOPS
– Get food, motor oil, coolant, brake fluid x3, fan belt, petrol
BUILD THE BASIC CAR BODY
– Sub Frame 4x10mm
– Wishbones 2x10mm each
– Spindles 1x12mm each
– Disc Brakes (wait until halfshafts are in place) 1x14mm each
– Steering Rack 4x9mm
– HalfShafts 3x9mm each
– Steering Rods (black bits facing inwards) 1x12mm each (Wait to tighten until Struts are installed.)
– Struts 4x9mm, 3x10mm, 1x12mm (12mm Bolt Shared with Steering Rods.)
– Steering Column 2x8mm
BACK WHEELS:
– Trail Arms 2x12mm each
– Coil Springs
– Drum Brakes 1x14mm each
– Shock Absorbers 1x12mm,2x6mm each
– Wheels 4x13mm each
– Gear Stick 3x6mm
– Fuel Strainer 1x8mm
– Gear Linkage 3x5mm
– Brake Lining (funky end left) 8x7mm (and 1 at each wheel)
– Clutch Lining 2x7mm
– Clutch Master Cylinder 1x9mm, 2x8mm
– Brake Master Cylinder 1x9mm, 2x8mm
– Battery
– Radiator 4x7mm
BUILD AN ENGINE
– Crankshaft
– Bearings 6x9mm
– Camshaft 2x5mm
– Camshaft gear 1x10mm
– Pistons 8x7mm
– Timing chain
– Timing cover 6x6mm
– Engine plate
– Flywheel 6x7mm
– Assemble clutch pressure plate, cover plate and clutch disc + attach to flywheel 6x6mm
– Crankshaft pulley 1x11mm
– Water pump 5x7mm
– Water pump pulley 4x7mm
– Fan belt
– Alternator 1x10mm, 1x 7mm, 1x Screwdriver
– Head Gasket
– Cylinder head 10x7mm
– Rocker Shaft 5x8mm
– Rocker Cover 6x7mm
– Oilpan 8x7mm
– Gearbox 6x7mm,1x13mm
– Drive Gear 7x6mm
– Distributor 1x6mm
– Oil Filter (Screw in)
– Spark Plugs (Screw in)
– Headers 5x8mm
– Carburettor 4x8mm
– Electrics
– Starter 2x7mm
– Fuel Pump 2x7mm
STICK THE ENGINE RIGHT UP THE CAR
(Hoist takes 2 x 10mm)
(Fitting takes 3 x 11mm)
FINISH UP THE BASICS
– Radiator hoses (top front, back bottom, central)
– Fuel Tank 7x11mm,1x12mm (at fuel line)
– Fuel Tank Pipe
– Exhaust 3x7mm (2 near engine, 1 near rear)
– Muffler 1x7mm
– Steering Wheel 1x10mm
– Handbrake 4x8mm 1x5mm
– Seats 4x9mm each (2x for back seat)
– Dashboard 2x10mm
– Dashboard Meters 2x6mm
STICK SOME OIL IN THE ENGINE, COOLANT IN THE RADIATOR & FLUID IN THE BRAKES/CLUTCH
WITH A SCREWDRIVER ADJUST THE ALTERNATOR & IDLE SCREW
WITH A 14mm ADJUST THE WHEELS
START HER UP! (and fix the inevitable problems)
MAKE ‘ER PRETTY:
– Hood 4x6mm
– Air Filter 2x6mm
– Doors 4x10mm each
– Fenders 5x5mm each
– Boot Lid 4x6mm
– Headlights 2x7mm each
– Grille 2x6mm
– Bumpers 2x8mm each
– Clock/RPM Gauge 2x7mm
(The rest just slots in)
If it’s drifting left or right, adjust the wheels
if it’s making a nasty whistling noise tighten the fan belt (by moving the alternator with a screwdriver)
if it’s smoking or overheating adjust the alternator & idle screw
enjoy!